universal ac input / full rangebuilt-in active pfc function, pf>0.95 high efficiency up to 88% protections: short circuit / overload / over voltage / over temperature emote on-off control stand by 5v@0.3ano load power consumption<0.5w (note.6) 5 years warranty withstand 300vac surge input for 5 secondscooling by free air convection built-in constant current limiting circuit 1u low profile 38mm built-in r built-in remote sense function specification hrpg-150-3.3 hrpg-150-5 hrpg-150-7.5 hrpg-150-12 hrpg-1 50-15 hrpg-150-24 hrpg-150-36 hrpg-150-48 model dc voltage rated current current range rated power ripple & noise (max.) note.2 output voltage adj. range voltage tolerance note.3 line regulation load regulation setup, rise time hold up time (typ.) voltage range note.5 frequency range power factor (typ.) efficiency (typ.) input environment inrush current (typ.) leakage current over temperature safety standards safety & emc (note 4) withstand voltage isolation resistance working temp. remote control working humidity storage temp., humidity temp. coefficient vibration mtbf dimension others note packing overload over voltage protection ac current (typ.) 3.3v 5v 7.5v 12v 15v 24v 36v 48v 30a 26a 20a 13a 10a 6.5a 4.3a 3.3a 0 ~ 30a 0 ~ 26a 0 ~ 20a 0 ~ 13a 0 ~ 10a 0 ~ 6.5a 0 ~ 4.3a 0 ~ 3.3a 99w 130w 150w 156w 150w 156w 154.8w 158.4w 80mvp-p 80mvp-p 100mvp-p 120mvp-p 150mvp-p 150mvp-p 200mv p-p 240mvp-p 2.8 ~ 3.8v 4.3 ~ 5.8v 6.8 ~ 9v 10.2 ~ 13.8v 13.5 ~ 18v 21.6 ~ 28.8v 28.8 ~ 39.6v 40.8 ~ 55 .2v 0.5% 0.5% 0.5% 0.3% 0.3% 0.2% 0.2% 0.2% 1.0% 1.0% 1.0% 0.5% 0.5% 0.5% 0.5% 0.5% 3000ms, 50ms/230vac 3000ms, 50ms/115vac at full load 16ms/230vac 16ms/115vac at full load 85 ~ 264vac 120 ~ 370vdc 47 ~ 63hz pf>0.95/230vac pf>0.99/115vac at full load 78.5% 84% 6 ~ 7v 9.4 ~ 10.9v 14.4 ~ 16.8v 18.8 ~ 21.8v 30 ~ 34.8v 41.4 ~ 48.6v 57.6 ~ 67.2v 86% 87% 87% 87% 88% 88% 2.3a/115vac 1.3a/230vac 35a/115vac 70a/230vac <1ma / 240vac 105 ~ 135% rated output power 3.96 ~ 4.62v protection type : constant current limiting, recovers automatica lly after fault condition is removed protection type : shut down o/p voltage, re-power on to recover protection type : o/p voltage, recovers automatically after temper ature goes down shut down ul60950-1, tuv en60950-1 approved compliance to en55022 (cispr22) class b, en61000-3-2,-3 compliance to en61000-4-2,3,4,5,6,8,11, en55024, en61000-6- 2, heavy industry level, criteria a i/p-o/p:3kvac i/p-fg:1.5kvac o/p-fg:0.5kvac i/p-o/p, i/p-fg, o/p-fg:100m ohms / 500vdc / 25 / 70% rh -40 ~ +70 (refer to "derating curve") rc+ / rc-: 4 ~ 10v or open = power on ; 0 ~ 0.8v or short = power off 20 ~ 90% rh non-condensing -40 ~ +85 , 10 ~ 95% rh 0.04%/ (0 ~ 50 10 ~ 500hz, 5g 10min./1cycle, 60min. each along x, y, z axes 213.4k hrs min. mil-hdbk-217f (25 ) 159*97*38mm (l*w*h) file name:hrpg-150-spec 2011-06-21 features : 1. all parameters not specially mentioned are measured at 230vac input, r ated load and 25 of ambient temperature. 2. ripple & noise are measured at 20mhz of bandwidth by using a 12" twisted pair- wire terminated with a 0.1uf & 47uf parallel capacitor. 3. tolerance : includes set up tolerance, line regulation and load regula tion. 4. the power supply is considered a component which will be installed into a fi nal equipment. the final equipment must be re-confirmed that it still me ets emc directives. 5. derating may be needed under low input voltages. please check the derati ng curve for more details. 6. no load power consumption<0.5w when rc- & rc+ (cn100 pin5,6) 0 ~ 8v or short. for guidance on how to perform these emc tests, please refer to ?emi testing of c omponent power supplies.? (as available on http://www.meanwell.com) h r p g - 1 5 0 s e r i e s 150w single output with pfc function function 0.63kg; 24pcs/16kg/0.76cuft 2.5% 2.5% 2.5% 1.5% 1.5% 1.5% 1.5% 1.5% 95 (3.3v ~ 7.5v) , 85 (12v ~ 48v) (tsw1 : d etect on heatsink q1 of power transistor) 105 (3.3v ~ 7.5v), 100 (12v ~ 48v) (tsw2 : d etect on heatsink hs4 of power transistor) 5v standby 5vsb : 5v@0.3a ; tolerance 5%, ripple : 50mvp-p(max.) emc immunity emc emission
mechanical specification case no.901i unit:mm terminal pin no. assignment pin no. pin no. 12 4,5 3 6,7 assignment assignment dc output -v dc output +v fg ac/l ac/n connector pin no. (cn100) : assignment pin no. 12 3 4 5 6 assignment -s +s auxg aux rc- rc+ mating housing or equivalent terminal or equivalent 4.5 9 152.5 7 150 6.5 18.5 78 97 84.5 65 3.5 24 159 22 117 9 28.5 3.5 3.5 18 3.5 38 6-m3(both sides) l=6 2-m3 l=4 detection circuit hrs df11-6dp-2dsa or equivalent hrs df11-6ds hrs df11-**sc 20 40 60 80 100 svr1 10 max. 12 3 4 5 6 7 9.5 8.2 6 4 25 3 1 cn100 without cover with cover ii 150w single output with pfc function file name:hrpg-150-spec 2011-06-21 derating curve output derating vs input voltage ambient temperature ( ) input voltage (v) 60hz ta = 25 85 100 125 135 155 264 100 90 80 70 60 50 40 load (%) load(%) -40 0 10 20 30 40 50 60 70 (horizontal) o.l.p. o.t.p. emi inrush active filter current limiting rectifiers & pfc i/p fg pwm pfc power aux switching power filter filter & & rectifiers rectifiers +v +s aux control control o.v.p. o.t.p. remote control -v -s auxg rc+ rc- h r p g - 1 5 0 s e r i e s block diagram fosc :100khz(3.3~7.5v) 70khz(12~48v)
fig 1.1 load - + the remote sensing compensates voltage drop on the load wiring up to 0.5v. 2.remote sense fig 2.1 - + load +s (pin2) sense lines should be twisted in pairs -s (pin1) 26 5 +s rc+ rc- remote control ground. turns the output on and off by electrical or dry contact between pin 5 (rc-). sho rt: power off, open: power on. positive sensing. the +s signal should be connected to the positive term inal of the load. the +s and -s leads should be twisted in pair to minimize noise pick-up effect. the maximum line drop compensation i s 0.5v. 4 3 aux auxg auxiliary voltage output, 4.75~5.25v, referenced to pin 3(auxg). t he maximum load current is 0.3a. this output has the built-in oring diodes and is not controlled by the "remote on/off control". auxiliary voltage output ground. the signal return is isolated from th e output terminals (+v & -v). cn100 6 4 25 3 1 cn100 6 4 25 3 1 +v +v -v -v 150w single output with pfc function file name:hrpg-150-spec 2011-06-21 function description of cn100 function manual pin no. function description +v +v -v -v rc+ rc+ 66 22 55 11 rc- rc- aux aux auxg auxg +s +s cn100 cn100 -s -s between rc-(pin5) and rc+(pin6) sw on (short) sw off (open) output status off on 1.remote control sw the psu can be turned on/off by using the "remote on/off" function h r p g - 1 5 0 s e r i e s 1 -s negative sensing. the -s signal should be connected to the negative term inal of the load. the -s and +s leads should be twisted in pair to minimize noise pick-up effect. the maximum line drop compensation i s 0.5v.
|
